Szukam opinii i porad na temat, jaki wybrac i gdzie kupic.
Chodzi mi o cos takiego:
http://www.scaleplasticandrail.com/kabo ... l-products
Punch & die set
- panzerflix
- Posty: 369
- Rejestracja: ndz 24 cze 2012, 04:56
Re: Punch & die set
Od 2 /3 lat szukam
- jest fajny na micromark w USA
- teraz w bytomiu mieli fajny czesi od zyletek
- jest fajny na micromark w USA
- teraz w bytomiu mieli fajny czesi od zyletek
You are not your thoughts. You are not your story. You are not your body.
Experience your thoughts, experience your story, experience your body, as none of it will last.
http://www.fromthetrunk.com | http://www.panzerflix.com
Experience your thoughts, experience your story, experience your body, as none of it will last.
http://www.fromthetrunk.com | http://www.panzerflix.com
Re: Punch & die set
A w Polsce gdzies mozna kupic Waldron'a?
- KFS-miniatures
- Posty: 6382
- Rejestracja: sob 23 cze 2012, 01:23
- Kontakt:
Re: Punch & die set
waldron moim zdaniem wyglada dosc tandetnie
nawiasem mówiac, mi szwagier zrobił taki próbny wybijak, zaraz zejde na dół, to wrzuce fote.. bo mozna by pomyślec o tym, żeby wdrożyc do produkcji jakiś zestawik..
nawiasem mówiac, mi szwagier zrobił taki próbny wybijak, zaraz zejde na dół, to wrzuce fote.. bo mozna by pomyślec o tym, żeby wdrożyc do produkcji jakiś zestawik..
Re: Punch & die set
Waldron ma o polowe mniej otworkow. Ten zestaw co pokazalem w pierwszym poscie wyglada bardzo dobrze, jest bogaty w otworki i cena nawet jest przystepna jak na tego typu przyrzad. Konkurencyjne produkty nie oferuja az tylu otworkow, a kosztuja zdecydowanie wiecej.
Re: Punch & die set
Reviews of these products can be found on Aeroscale in the "REVIEWS" section.
ATTENTION: Shipping prices for international customers have risen due to the drastic increases in USPS International Shipping Rates.
REGULAR WHEEL SANDER $26USD Max. wheel thickness 3/8" (9,5mm) Max. wheel diameter 3/4" (19mm)
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
LARGE WHEEL SANDER $31USD Max. wheel thickness 5/8" (15,8mm) Max. wheel diameter 1 1/2" (38,1mm)
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
LANDING GEAR JIG $41USD
USA shipping $9USD
Canada shipping $14USD
All other shipping $21USD
PUNCH & DIE SET $47USD
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
PayPal to this email address, or if you are in the USA, check or money order to:
Chad Bowser
416 Zachary Drive
Manheim, PA 17545
ATTENTION: Items shipped outside the USA will not be devalued or claimed as a gift for customs purposes. The Buyer is responsible for any and all additional fees such as VAT's, import duties, customs charges, etc. These fees ARE NOT included in the shipping charges.
Contact me for additional shipping rates on multiple items.
ATTENTION: Shipping prices for international customers have risen due to the drastic increases in USPS International Shipping Rates.
REGULAR WHEEL SANDER $26USD Max. wheel thickness 3/8" (9,5mm) Max. wheel diameter 3/4" (19mm)
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
LARGE WHEEL SANDER $31USD Max. wheel thickness 5/8" (15,8mm) Max. wheel diameter 1 1/2" (38,1mm)
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
LANDING GEAR JIG $41USD
USA shipping $9USD
Canada shipping $14USD
All other shipping $21USD
PUNCH & DIE SET $47USD
USA shipping $6USD
Canada shipping $12USD
All other shipping $16USD
PayPal to this email address, or if you are in the USA, check or money order to:
Chad Bowser
416 Zachary Drive
Manheim, PA 17545
ATTENTION: Items shipped outside the USA will not be devalued or claimed as a gift for customs purposes. The Buyer is responsible for any and all additional fees such as VAT's, import duties, customs charges, etc. These fees ARE NOT included in the shipping charges.
Contact me for additional shipping rates on multiple items.
Re: Punch & die set
A te czeskie oglądałeś w Bytomiu?
Komentarze na polskich forach dyskusyjnych? Tak ja to widzę:
Re: Punch & die set
Patrzylem, ale jakos mnie nie przekonaly.
-
- Posty: 194
- Rejestracja: wt 06 lis 2012, 00:39
Re: Punch & die set
Używałem wczoraj tego ustrojstwa (http://www.perthmilitarymodelling.com/r ... /aedpd.htm). Potrzebowałem wybić krążek w którym jest otwór, więc najpierw wybiłem mniejszy otwór a następnie krążek, wszystko poszło ładnie i gładko, krawędzie ostre, bez wklęśnięć na brzegach.
Re: Punch & die set
Ten Hexagonal bym przytulil.